GRAPHIC: Link to International Mold Steel welcome page.
CONTACT US  
800.625.6653  
 
Home | About Us | What's New | Webinars | Videos | Contact Us
 

HOME --> PLASTIC MOLD STEELS --> PORCERAX II --> POST-MACHINING TREATMENTS

Plastic Mold Steels

Porcerax II

Post-Machining Treatments

Heat Treatment
Heat treating of Porcerax II should be done in a vacuum furnace. As supplied, Porcerax II has a hardness of 35-40 HRC. It can be heat treated to 50-52 HRC; however, Porcerax II carries a fairly high potential for movement. Strict guidelines are supplied by International Mold Steel and should be followed.

Hardness
Porcerax II is 25% porosity by volume and will give false or misleading readings if tested with either a Rockwell or Brinell hardness tester. As the load of either of these testers is applied, the pores beneath the surface will collapse and render a false reading. It is recommended that a micro Vickers hardness tester (50 or 30g load) be used to test the hardness of Porcerax II.

Texturing
Porcerax II (7 micron grade) can be textured. In order to prevent the possibility of destroying the internal vent structure of the material, certain procedures must be strictly adhered to. It is imperative that the chosen texture source know they are working with Porcerax II. If they don't, the likelihood for permanent, irreparable damage to the piece is virtually assured.

The pores of the material must be thoroughly cleaned and properly sealed prior to texturing. Failure to do so results in the etchants used in the texturing process leaching into the pore structure and rusting the venting closed. This rust is permanent and cannot be removed once it has occurred. The piece will be useless and must be replaced.

Thousands of molds worldwide have been successfully textured. However, it is imperative that the molder and/or moldmaker's texture source be supplied with the information needed from International Mold Steel to properly process the piece.
  
We strongly advise against inserting Porcerax II into an already textured surface. The perfect venting of Porcerax II results in much higher resolution of the grain at the inserted area and a dramatic reduction in gloss. It is recommended that the entire textured surface be Porcerax II. Also, due to the pre-treatment procedure required for texturing Porcerax II, expect longer deliveries and higher costs. Please consult your graining source for more information.

Surface Reproduction
Porcerax II provides perfect venting of all gases from the mold. While this is desirable in most cases, the venting of the Porcerax produces a perfect "marriage" between the resin and the molding surface, thus producing a dull, matte finish. If Porcerax II is used as an insert on the cavity side, the result will be two dissimilar appearances due to differences in gloss and texture definition. This may be acceptable if the parts are painted after molding.

Water Lines
Occasionally the need will arise, due to size or application considerations, to water-cool Porcerax II. There are a number of ways to accomplish this. In designs that involve a straight-through water line pattern, a simple, effective way to seal the line and prevent leakage is electroless-nickel plate the water lines. In complex circuit-type patterns, it is advisable to use an acceptable sealant such as Dichtol. Electroless nickel has a tendency to pull away from sharp corners such as those at intersections of crossing water lines. However minutely this pulling away from corners may be, it will eventually cause some leakage into the material and reduce permeability through oxidation. Improper use of the Dichtol sealant will produce the same results. Regardless of which sealing process is used, be absolutely certain the material has been thoroughly cleaned of any residual machining fluids or other contaminants.


Important Warning:

It is imperative that anyone coming into contact with Porcerax II during the mold building or molding operations understand the characteristics and sensitivity of this material. Any questions should be directed to International Mold Steel at 1.800.625.6653.


NOTE: All technical and engineering data and suggested procedures, specifications and applications contained in this publication are for general information only. Sintokogio, Ltd., International Mold Steel and/or their distributors disclaim any and all express or implied warranties of merchantability, suitability for any particular purpose or use, or freedom from infringement of any patent, trademark or copyright. Porcerax II® is a registered trademark of International Mold Steel, Inc. and Sintokogio, Ltd..

 

PORCERAX II

Products

Accessories

Recommended Reading

Unique Characteristics

Benefits

General Properties

Post-Machining Treatments

Water Line Sealing

Design Guidelines

Cleaning, Maintenance, and Resin Removal

Porcerax II Insert Installation

Porcerax II Pin Installation

Porcerax II Stock List

Discussion Forums

Sustainability

 

 
 
  International Mold Steel, Inc. 
6796 Powerline Drive 
Florence, KY 41042 USA 
Toll Free: 800.625.6653
Tel: 859.342.6000
Fax: 859.342.6006
Sales E-mail: salesdesk@imsteel.com
Literature E-mail: info@imsteel.com
Web: www.imsteel.com


www.imsteel.com